GSC Mitsubishi Evo IV-VIII Billet Camshafts

Billet Cams.jpg
Billet Cams.jpg

GSC Mitsubishi Evo IV-VIII Billet Camshafts

599.25

GSC has become a name synonymous with quality camshafts in the 2JZ community. With billet construction and camshaft profiles ranging from mild to wild, their S1, S2, and S3 camshafts are perfect for cars ranging from basic street builds up to race cars searching for every last horsepower.

 

S1

The Billet GSC Power-Division S1 cams for the Mitsu Evolution 4-8 are designed for those with the stock turbo up to the 550WHP Stock location or aftermarket turbo kits. These cams will not sacrifice any bottom end loss over stock cams; nothing but gains and will promote faster spooling of the upgraded turbos. Gains of 30-55whp (depending on Turbo) have been seen by simply bolting the S1 cams in. Designed for a rev range of 3000-7500rpms, these cams work well on the stock valve springs with lower boost and RPM goals.  Idle is slightly rougher than stock. Made 100% In The USA!


**If using aftermarket cam gears(especially AEM) check the bolt lenght, some cam gears are too thick for the OEM bolt on the Billet cams, a 40mm underhead length bolt may be necessary in this case**

 

S2

The Mitsubishi Evo 4-8 Bilet S2 cams are designed for those with a goal of 400-700whp. No low end power is lost vs the stock cams when used with the larger turbos. The S2 cams will show gains of 50-70whp over the stock cams and in some cases more in the higher RPMS. Great for 2.0L engines with stock frame turbos revving to 9000rpms or for Stroker motors revving to 8000rpms. The S2 Cams are suggest to run on our upgraded Beehive valve spring replacement or full Beehive valve spring kit with Titanium retainer.

 

  • Designed for a rev range of 4000-9000 RPMS (2.0L or 3000-8000 2.2L+)
  • S2 cams can run on Factory ECU with custom flashing
  • Made 100% In The USA!


**If using aftermarket cam gears(especially AEM) check the bolt lenght, some cam gears are too thick for the OEM bolt on the Billet cams, a 40mm underhead length bolt may be necessary in this case**

 

S3

The Billet S3 Cams for the Evo 4-8 4G63. These cams are meant for the 800whp+ to take advantage of a very large turbo. these are NOT suggested for anyone running smaller than the 67mm to GT42R turbo.


**If using aftermarket cam gears(especially AEM) check the bolt lenght, some cam gears are too thick for the OEM bolt on the Billet cams, a 40mm underhead length bolt may be necessary in this case**

 

R2

We worked with English Racing on this profile to offer the 2.2-2.4L lower reving engines a profile that would allow for more air volume in the cylinder to help fill the larger displacement engines and make more midrange and top end power. The 7008R2 is a high lift very aggressive profile with a short overall duration to keep a lower usable rpm band. The 7008R2 is designed to rev between 4000-8500 rpms and should be used with a stroked engine or added displacement engine. The peak lift of 12.0MM Intake and exhaust will require upgraded valve springs and a titanium retainer with special attention to seal to retainer clearance. With the lift of this profile it is suggested to only use the 5041/5040 Ti retainer and spring kits do to valve seal to retainer clearance. The 5041 can be used to 40+psi and the 5040 to 32psi on the R2 profile at 8500rpms without float or flutter issues. The profile will work fine on the OEM Rocker Arm and the Zero-tick lifter or with the OEM lifter. We have seen gains of 25-30whp over the S2 profile on the stroked applications with much more possible when used with a ported head and aftermarket intake manifold. .


**If using aftermarket cam gears(especially AEM) check the bolt lenght, some cam gears are too thick for the OEM bolt on the Billet cams, a 40mm underhead length bolt may be necessary in this case**

Select Your Camshaft:
Quantity:
Add To Cart